Floor Sanding & Fitting Project Gallery

Project Overview

This project in Walworth involved fitting engineered wood flooring with an acoustic underlay across the main floor of a first-floor flat. The clients had an older, worn floor that they wanted to replace with a stylish but practical alternative. They chose a rustic-grade engineered oak for its character and warmth, and our recommendation to use a high-performance acoustic underlay was accepted immediately, given their concern about noise impact on the flat below. The job covered the living room, hallway and two bedrooms.

The Challenge

The main challenge on this project was meeting the building's noise reduction requirements while also keeping the floor height increase to a minimum. High-performance acoustic underlays are thicker than standard foam underlays, which adds height. In this flat, several doorframes had limited clearance and we had to confirm the finished floor height before proceeding to ensure doors would clear the new surface. A couple of doors required the bottoms trimming once the floor was in, which we carried out on site.

Our Approach

• Strip-out: The old flooring was removed and the subfloor inspected for level and stability.
• Door height check: All internal doors were measured against the planned finished floor height to identify which ones would need trimming.
• Acoustic underlay: The specified acoustic underlay was laid and taped at all joints to form a continuous layer, providing both impact sound and thermal insulation.
• Engineered wood fitting: Rustic oak engineered boards were laid using a floating click-lock method, maintaining consistent expansion gaps at all walls and fixed points.
• Door trimming: Two internal doors were planed along the bottom edge on site to clear the new floor level.
• Trims: Matching beading and transition strips were fitted throughout to give a clean finish at all edges.

The Result

The finished floor looked excellent and the acoustic performance was immediately apparent -- the clients noticed a significant reduction in the hollow sound underfoot compared with the previous flooring. The rustic oak character added warmth and personality to the rooms. Engineered wood flooring supply and fit in London typically costs between £35 and £60 per square metre depending on the grade and profile chosen, with acoustic underlays adding a modest premium over standard products. The overall result was a floor the clients were very happy with and that met all the building's requirements.

Frequently Asked Questions

Does all flooring in flats need an acoustic underlay?
Most leases for flats in England and Wales include a requirement for floor coverings to meet a minimum impact sound reduction standard. We always recommend checking your lease before fitting and can advise on underlay specifications that meet typical requirements.

What is rustic grade engineered wood?
Rustic grade boards include a greater number of natural features such as knots, colour variation and grain character. This is different from prime or select grade, which is more uniform. Rustic grade is popular for its warmer and more natural appearance.

Can engineered wood be fitted over underfloor heating?
Yes, engineered wood is generally more stable than solid wood and well suited to use over underfloor heating systems. Board thickness and species affect how efficiently heat transfers through, and we can advise on the best options at the survey stage.

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Project Overview

This engineered wood flooring installation in Abbey Wood replaced a solid wood floor that had been damaged beyond economical repair by repeated moisture fluctuations. The clients had chosen to move to engineered boards, which have a more dimensionally stable construction and are better suited to homes where humidity levels vary throughout the year. We fitted the new floor across the ground floor of the property, covering the living room, dining area and hallway.

The Challenge

The existing subfloor had been affected by the same moisture issues that had damaged the old solid wood floor. Before the new engineered boards could go down, the subfloor needed to be dried out properly and in some areas replaced where it had deteriorated. We also needed to identify and address the source of the moisture ingress before fitting -- there was no point fitting a new floor on a subfloor that was still damp. The moisture issue turned out to be a failed damp-proof membrane in part of the ground floor, which was treated and sealed before we proceeded.

Our Approach

• Subfloor investigation: Moisture readings were taken across the full area before any work began. Problem areas were mapped and the source of moisture identified.
• Remediation: The failed damp-proof membrane section was treated. Affected subfloor sections were replaced and allowed to dry to an acceptable moisture level before fitting.
• Acclimatisation: Engineered boards were left in the property for several days to adjust to the ambient conditions before fitting began.
• Installation: Boards were glued down to the subfloor rather than floated, which provides a more stable result in an environment with known moisture history. Gluing down also eliminates the hollow sound underfoot that floating installations can sometimes produce.
• Finishing: Expansion gaps were fitted at all walls and covered with matching beading. A final protective oil coat was applied across the whole floor.

The Result

The new floor looked fantastic and the clients immediately noticed how much more stable and solid it felt compared with the old floor in its later years. By addressing the moisture issue properly before fitting, we gave the new floor the best possible start. Engineered wood flooring supply and installation typically runs between £35 and £60 per square metre. The additional work on the subfloor was costed separately and transparently, and the clients felt the overall investment was excellent value given the quality of the result.

Frequently Asked Questions

Why is engineered wood more stable than solid wood?
Engineered wood has a real wood top layer bonded to a core made of multiple layers of plywood or HDF. These layers are laid at opposing angles, which counteracts the natural tendency of wood to expand and contract with moisture changes. This makes it more suitable for ground floors and environments with variable humidity.

Should engineered wood be glued down or floated?
Both methods work well in different circumstances. Gluing down is preferable where the subfloor has a history of moisture issues or where a very solid feel underfoot is required. Floating is faster and makes the floor easier to remove in future if needed. We advise on the best method at the survey stage.

Do you cover Abbey Wood and southeast London?
Yes. We work across southeast London including Abbey Wood, Woolwich, Plumstead and the wider DA and SE postcode areas.

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Project Overview

This project in Northwest London involved fitting engineered wood flooring along with a full set of flooring accessories to achieve a complete, professional finish throughout the property. The clients had selected the boards themselves and asked us to supply all the accessories -- skirting, beading, threshold strips, and reducer profiles -- and to fit everything as a complete package. The project covered multiple rooms across two floors, each with slightly different subfloor conditions and doorframe configurations.

The Challenge

Managing accessories across a multi-room project requires accurate pre-measurement and coordination to ensure consistent materials throughout. Different rooms also had different transition requirements -- some doorways connected rooms at the same level while others had small height differences that needed reducer strips rather than flat transitions. Matching all accessories to the board tone required careful selection, and a couple of the original samples supplied did not match well enough, so we arranged alternatives before the fit day.

Our Approach

• Pre-fit survey: All rooms were measured and accessory requirements calculated in detail to avoid any shortfalls on the day.
• Subfloor preparation: Any uneven areas were levelled and the subfloor cleaned before fitting began.
• Board fitting: Engineered boards were laid room by room using a floating method, maintaining consistent expansion gaps and staggering joints between rows.
• Skirting installation: Existing skirting was removed and replaced with new matching skirting boards, neatly mitred at corners and scribed to any uneven walls.
• Threshold and transition strips: All doorway transitions were fitted with the appropriate profile -- flat T-bars where floors met at the same height and reducers where there was a step.
• Beading: Floor-to-skirting beading was used in areas where the existing skirting was retained, to cover the expansion gap cleanly.

The Result

The completed project had a consistent, polished look throughout the property. Having matching accessories fitted at the same time as the floor made a significant difference to the finished appearance -- all transitions and edges were neat and intentional rather than an afterthought. Engineered wood floor installation in London costs between £35 and £60 per square metre for the boards and fitting, with accessories and skirting costed separately. The clients were very pleased with the result and the way all elements came together as a single cohesive floor.

Frequently Asked Questions

What flooring accessories are typically needed for an installation?
Most installations need at minimum some form of edge trim or beading to cover the expansion gap at the walls, and transition strips at all doorways. Skirting boards are fitted where the existing skirting is being replaced. Reducers or ramp profiles are needed where the new floor meets a lower surface such as tiles or carpet.

Do you supply accessories as well as fit them?
Yes. We can supply a full range of accessories that are matched or co-ordinated to the boards. This saves clients the time of sourcing each component separately and ensures compatibility.

Can engineered wood be fitted on the first floor as well as the ground floor?
Yes. Engineered wood is suitable for any floor level. On upper floors, we always check the subfloor condition and recommend an acoustic underlay where noise transmission to the floor below is a concern.

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Project Overview

This project in Willesden was one of the most varied we have undertaken in a single residential property. The scope included engineered wood flooring installation in the main living areas, vinyl flooring in the kitchen and bathroom, hardwood floor sanding, buffing and lacquering in an existing bedroom floor, and gap filling and staining in the hallway. The clients were doing a full refurbishment and wanted all flooring handled by a single contractor to keep coordination simple and the finished look consistent across the property.

The Challenge

Managing multiple flooring types simultaneously in a single property requires careful scheduling so that wet processes such as staining and lacquering do not hold up other areas or get contaminated by dust from sanding. We planned the sequence carefully: strip-out and subfloor preparation first across the whole property, then vinyl installation in the wet rooms, followed by engineered fitting in the living rooms, and finally sanding, staining and lacquering in the bedroom and hallway after all other work was complete. Keeping the dust from the sanding operation contained was also important given the fresh installations elsewhere.

Our Approach

• Sequencing: A detailed daily schedule was agreed before work began to ensure each trade area was ready before the relevant team moved in.
• Vinyl fitting: Kitchen and bathroom vinyl was cut and laid on prepared subfloors with full adhesive bonding to prevent movement in wet conditions.
• Engineered fitting: Living room engineered boards were laid floating over an acoustic underlay, with expansion gaps maintained throughout.
• Gap filling and sanding: The hallway hardwood received gap filling first, followed by machine sanding once the filler had cured.
• Staining: A warm mid-tone stain was applied to the hallway to tie it visually to the engineered boards in the adjacent rooms.
• Lacquering: All sanded areas received two coats of satin lacquer to complete the job.

The Result

The finished property had a consistent, well-thought-out flooring scheme throughout. The stained hallway bridged the gap between the new engineered boards in the reception rooms and the existing bedroom floor, making the whole ground floor feel connected. The vinyl in the wet rooms was practical and looked sharp. Having one contractor handle everything saved the clients a considerable amount of coordination time and produced a result that felt planned rather than piecemeal. Fitting costs typically run between £35 and £60 per square metre for engineered boards, with sanding and finishing at £25 to £45 per square metre for the restoration elements.

Frequently Asked Questions

Can you handle multiple flooring types in one project?
Yes. We regularly work on properties where different rooms require different flooring solutions. Managing the sequencing and transitions between floor types is something we plan carefully at the survey stage.

What are the benefits of vinyl flooring in kitchens and bathrooms?
Modern vinyl flooring is fully waterproof, easy to clean, warm underfoot and available in a wide range of designs including stone and wood looks. It can also be fitted over most existing subfloors without the height build-up of other options.

Do you work in Willesden and the NW10 area?
Yes. We cover Willesden, Harlesden, Cricklewood, Kilburn and the surrounding north-west London postcodes. Contact us to arrange a free survey.

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Project Overview

This project involved the professional installation of parquet flooring at a property in Balham, SW12. The client required a quality floor that would stand up to daily use and complement their interior. Our fitting team assessed the subfloor condition, carried out any necessary preparation work, and fitted the new floor to a high standard.

Before the Work

Prior to installation, the existing floor covering was inspected and the subfloor was prepared to ensure it was flat, dry, and suitable for the new parquet. Any existing floor covering was lifted and disposed of cleanly before the fitting work began.

Survey photos showing the floor condition before work:

Our Approach

The following services were carried out as part of this project:

• Doors Plus Frame Trimming (per door)
• Parquet Floor Fitting - With Border
• Skirting Boards Installation (excl. materials)
• Subfloor Preparation (ply 12 mm)
• Thresholds & Fitting (inc. materials)
• Solid Oak Corner Bead, Lacquered, 15 mm, 2.4 m
• DPM application

The Result

The completed parquet installation looked clean and finished throughout. Joins are tight, edges are neat, and the floor sits flat and stable. Beading and threshold strips were fitted where required to complete the job properly. The client was pleased with both the quality of the work and the appearance of the new floor.

Photos of the completed work:

Frequently Asked Questions

How long does parquet installation in Balham, SW12 take?
Most fitting jobs are completed within one to two days. Larger areas or more detailed layouts such as herringbone patterns take longer due to the additional cutting and positioning involved.

Do I need underlay?
Yes, underlay is required for most floor types and helps with insulation, sound deadening, and levelling minor subfloor imperfections. We can supply and fit appropriate underlay as part of the installation.

How much does floor fitting cost in Balham, SW12?
Fitting costs typically range from £70 to £100 per square metre depending on floor type and complexity. We provide a full written quote before starting any work.

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Project Overview

This project involved the professional installation of engineered wood flooring at a property in Islington, N1. The client required a quality floor that would stand up to daily use and complement their interior. Our fitting team assessed the subfloor condition, carried out any necessary preparation work, and fitted the new floor to a high standard.

Before the Work

Prior to installation, the existing floor covering was inspected and the subfloor was prepared to ensure it was flat, dry, and suitable for the new engineered wood. Any existing floor covering was lifted and disposed of cleanly before the fitting work began.

Survey photos showing the floor condition before work:

Our Approach

The following services were carried out as part of this project:

• Door Frame Trimming
• Doors Plus Frame Trimming (per door)
• Engineered Flooring Installation
• Furniture Moving
• Lift & Dispose Hardwood Flooring

The Result

The completed engineered wood installation looked clean and finished throughout. Joins are tight, edges are neat, and the floor sits flat and stable. Beading and threshold strips were fitted where required to complete the job properly. The client was pleased with both the quality of the work and the appearance of the new floor.

Photos of the completed work:

Frequently Asked Questions

How long does engineered wood installation take?
Most fitting jobs are completed within one to two days. Larger areas or more detailed layouts such as herringbone patterns take longer due to the additional cutting and positioning involved.

Do I need underlay?
Yes, underlay is required for most floor types and helps with insulation, sound deadening, and levelling minor subfloor imperfections. We can supply and fit appropriate underlay as part of the installation.

How much does floor fitting cost in London?
Fitting costs typically range from £35 to £60 per square metre depending on floor type and complexity. We provide a full written quote before starting any work.

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Project Overview

This project involved the professional installation of engineered wood flooring at a property in Greenford, UB6. The client required a quality floor that would stand up to daily use and complement their interior. Our fitting team assessed the subfloor condition, carried out any necessary preparation work, and fitted the new floor to a high standard.

Before the Work

Prior to installation, the existing floor covering was inspected and the subfloor was prepared to ensure it was flat, dry, and suitable for the new engineered wood. Any existing floor covering was lifted and disposed of cleanly before the fitting work began.

Our Approach

The following services were carried out as part of this project:

• Door Frame Trimming
• Engineered Flooring Installation
• Thresholds & Fitting (inc. materials)

The Result

The completed engineered wood installation looked clean and finished throughout. Joins are tight, edges are neat, and the floor sits flat and stable. Beading and threshold strips were fitted where required to complete the job properly. The client was pleased with both the quality of the work and the appearance of the new floor.

Photos of the completed work:

Frequently Asked Questions

How long does engineered wood installation in Greenford, UB6 take?
Most fitting jobs are completed within one to two days. Larger areas or more detailed layouts such as herringbone patterns take longer due to the additional cutting and positioning involved.

Do I need underlay?
Yes, underlay is required for most floor types and helps with insulation, sound deadening, and levelling minor subfloor imperfections. We can supply and fit appropriate underlay as part of the installation.

How much does floor fitting cost in Greenford, UB6?
Fitting costs typically range from £35 to £60 per square metre depending on floor type and complexity. We provide a full written quote before starting any work.

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit

Have a similar project? Call us on 020 88309782 or Book a Free Site Visit